Blown Nitro Fuel Altered TFX - $62,500

Listed By jimoverly
Blown Nitro Fuel Altered TFX
$62,500
Private Seller - jimoverly
PARKERSBURG, WV , US
Classifieds Message Seller + Add to Favorites
Report This Ad

Item Details

Ad Number184023736
ConditionUsed

Description

Complete Blown Nitro Fuel Altered car with spares, tools and special equipment.

Car will cert 6.0

526 CI Outlaw TFX 2000 engine – never hurt in any way. AJPE Stage 3 fuel heads (w down nozzles), 4.375 X 4.375 bore and stroke. 30 gallon Hilborn pump. 14-71 Std helix Mooneyham stripped for nitro. Dual Points mags (SuperMag 5s hopped up), Single and dual valve covers. Fabricated for single and Stage 5 for dual plugs, Erson nitro grind cam. Arias Pistons, Bill Miller rods all new. Rods, rings and pistons are fresh and have never been fired. Enderle Birdcatcher, K-style barrel valve, Dale Emory Hi/Lo system to get some heat in the motor before a run, 25% Lenco CS1 2 speed. Lenco reverser. Strange/Moser rear end. Rear has 2 passes on it since completely rebuilt- 4:10 gears. Dual Wilwood 4-puck calipers, each rear wheel. SPE spot disks on front. RPM data logger with 28 channels. Brand new digital RPM Dash. 10-lb and 5-lb fire bottles. Dual chutes, Engine diaper, blower bag, injector restraint, Lenco blanket. 120 wheelbase chrome moly chassis. Spindle mounts fronts. Double bead lock rears. 34.5 X 17 X 16 rears tires. Wheelie bars. Tall wing (not mounted) and short wing (rears) new front wing (unmounted). 23 Bucket T body. The car will .950 60-ft all day long. Never run over 8th mile since built. Titanium 3-disk Glide clutch (1 3/8”-10) 6 stand (small stand) - Jeff Johnson flanged, o-ringed oil pan (fewer bolts to get off than the TFX pan rail design). System 1 30-GPM oil pump (wet sump), 3-qt oil accumulator. The car has a Racing Radio set up for the driver

Details on RPM data logger- all EGTs, fuel pressure (x 2, one at the pump, one on the engine side of barrel valve) fuel flow, manifold temp, manifold pressure, crank speed, rear input shaft speed, oil pressure, accelerometer. The master logger was just upgraded by RPM to run the new digital dash.

The spares-

**Complete set of brand new completely rebuilt heads**

All new valves, guides, springs, springs seats, keepers, retainers, valve seats and –wire o-rings. Inconel exhaust and titanium intakes. (Same as the heads on the car).

**Spare SuperMag 5s (2) hopped up, with wire sets and coils**

**Lenco**

25% gear set- clutch set

Lenco reverser gear set

Seals and bearings, levers, air pod, shift handles

**Band new Crower crank 4.375 (dual keyway)**

**2 sets of Bill Miller Rods**

**3 Arias pistons**

**Boxes and boxes of main and rod bearings (over $3K in bearings)**

**Many floaters and disks**

**Selection of input shafts and output shafts.**

**Spare Kieth Black oil pump**

**2 spare Hilborn PG 250 (#5s) pumps-30 GPM**

**30-GPM Waterman knockoff pump made by Gerardo (looks like a non-anodized Big Bertha)**

**45/55/65 GPM gearbox pump (depending on gear set installed) by Dave Benjamin**

**Enderle big show (1990s) barrel valves (3)- very tunable-ask Spike Gorr!**

**Enderle magnesium Buzzard catcher**

**Lots of fuel fittings and hoses, from -20 to -3**

**Big show TDK style valves.**

**30 gallons of Brad Penn 70 wt nitro oil (and 30 more gallons of recovered oil)**

**Blower pulleys (13.9) about 15 of them**

**5 new Kevlar belts**

**2 single mag drives with mechanical tach drive**

**Stahl 10 RPM mechanical tach with tattletale**

**Spare Taylor wire sets.**

**MSD wire grabber sets (handles)**

**Spare used set of funny car style headers ( no exhaust bungs- but I have a set that goes with the car), Jet-Hot coated**

**Zoomie style headers**

**Spare pushrods**

**Complete spare lifter set**

**New blower idler pulley and T-bolt set**

**Spare CO2 bottle for shifter, spare regulator for shifter**

**T straps for blower restraints (mounts to header bolts)**

**Spark plugs –around 100 (Autolite 5383)**

**All kinds of nozzles and fuel system parts-poppets, springs, spacers, and poppet tester, pills, nozzle racks, nozzle holders (aerated on non-aerated)**

**Spare K-style barrel valve**

**Several shutoff valves -12 and -10**

**Complete gear drive and cover**

**And enough nitro to get you going.**

**Tools and equipment that goes with it:**

**Pro jacks style jacks - complete set**

**Piston installers (4.375)**

**Nitro hydrometer set (the good one with three hydrometers)**

**Kestral 250 weather station**

**Complete set of racing radios**

**Buzz box**

**Bearing cap puller**

**Piston installation guides and rod bolt sleeves**

**Small style blower starter and battery pack and battery tray (uses 3 lawn tractor batteries)**

**Spare cables for starter**

**4 new Darton sleeves (already honed to 4 .375)**

**8 used spare sleeves**

**3-2A/20 2-piece fire suit (Simpson) Red 2 XL**

**Fire boots –large**

**3-2A/20 gloves w/ arm restraints**

**Hans device – large**

**Neck brace**

**Balaclavas (2)**

**Nomex socks**

**Leak down tester**

**Impact nitro (breathers) helmet with Racing radio speakers installed. Large**

**Complete clutch box with everything needed for the clutch, nuts, bolts, etc.**

**Lenco service box with oil sump**

**Rear endplate to set up rear ends on the bench**

**Large battery tray**

**Complete 30-gallon oil recovery system to settle nitro out on the engine oil. This allows you to reuse some oil with new.**

**About 20 5-gallon fuel jugs**

**About 20 2 ½ gallon oil containers bought new for oil recovery)**

**And I have surely left lots of things out. The idea here is that I want to sell the car, all spares for it and anything that is uniquely for the car - and my personal safety gear. I’m done racing and would like to see this go to a NEW OWNER-not somebody who’s going to part it out to make a buck.**

**Call me at my shop (304) 464 2008. Eastern time. Leave a message. I’m a one-man show and can’t always stop to get the phone.

Left off original list: (items with * are on the car)

*Custom made Smiley’s header w/ EGT bungs-double wall
*Throttle stops
*Dunn dual Mag drive
*Brake 2 psi residual (on front brakes)
*Stanke Injector air bleed
*On board 12 V battery charger for the Data logger



Aluminum tool tray 36” x 36” – mounts on frame rails for between round servicing
Small tool tray for top of injector
Spare Aluminized parachute bags (3)
Spare chute (2)
Cast aluminum single plug valve covers
Cast magnesium single plug Valve covers (Kid Presto)
Cast powder coated aluminum Ansen valve covers –single plug (Hemi orange)
SPE funny car steering box with output shaft
36 Volt battery charger
Blower starter storage box –polished diamond plate
3 full 5 lb fire bottles
Full spare 10 # fire bottle
Breathing air bottle and brackets
2 Spare pilot chutes w/springs
One spare chute pack mounting plate
Starting line air tank
Tire covers
20 ton low pressure air bag (for transporting car safely)
Head studs
Complete set of spare lifters
Spare pushrods
Fuel system return springs
Injector arms and heim joints
Pill holders
Fuel pick up and return manifolds
System 1 spare filter and rebuild kit
About 20 copper head gaskets
10 full face gas masks
Titanium down nozzle manifolds and jumpers
Stainless down nozzle manifolds and jumpers
Engine o-ring sets
Crank oil seal holders
Spare engine diaper
Lenco 3 speed blanket
Spare Stainless injector lines
Spare oil pump drive shafts
Oil pump drill drive shaft
Spare pressure gauges
#2 CO2 cylinder (for refilling shifter bottle)
Complete spare set of rings
Hundreds of Zues and other ¼ turn fasteners
Tow straps (several)
Fuel funnels
About 20 Anodized Aluminum AN wrenches -3 to -20
Clutch pack rack
Piston/rod rack
Spark plug racks
Nozzle racks w/ hundreds of nozzles - 20s to 90s
Wilwood brake spares
Spare dual brake master cylinder
Spare proportioning valve
Torque limiting spark plug wrench
Spare -20 oil hose w/ fittings
Box of AN hose, various sizes
Box of AN fittings—quite a few of various sizes
Lots of spare clutch floaters and disks-brand new and lots of used, serviceable.
New Sleeve extractor (for 4.375 and one extra head for 4.187 and 4.230)
Fuel distribution Wyes and hoses
Soda syrup can (can be pressurized) for warming up on methanol
Koul Tools for AN hose -3 to -16
ETC magneto rev limiter-never installed
Head stands (for working on heads)
Fire bottle heads and nozzles
9” 4.29 Pro Gear set
Lakewood Can shipping box
Mooneyham shipping box
Crankshaft shipping Box

Payment Details

Trades Accepted
Accepted Payment Methods Cash

Seller Notes

Possibly

Message Seller

Send Message



I agree to receive emails from RacingJunk.com . I understand that I can unsubscribe at any time.
Privacy Policy

About The Seller

PRIVATE SELLER
jimoverly
Member Since June 2009
CONTACT INFORMATION
PARKERSBURG, WV 26104
Show phone number


Honor Payments
Lifetime: 0
Last 12 months: 0 Learn More
No Achievements Yet
Bronze Seller Silver Seller Gold Seller Platinum Seller Power Seller
Get Transportation Rates

Location

View All Resources

Buyer Resources

Similar Classifieds
Copyright © 2005-2021 MH Sub I, LLC dba Internet Brands All Rights Reserved.

Designated trademarks and brands are the property of their respective owners. Use of this Web site constitutes acceptance of the RacingJunk.com
Terms of Use, Classifieds Disclaimer, Privacy Policy, Cookie Policy and
Do Not Sell My Personal Information

Internet Brands